Electronic key GROM Airsoft LITE PLUS

Electronic key GROM is made on the base of the 3d generation MOS transistors and has the following characteristics:

 

  • Designed for stable operation of drives (gears)at loads up to 200 m\s.

  • Key dimensions 27х7х12 mm.

  • The key module is filled with an epoxy res in compound of a higher thermal conductivity, which means a complete sealing of the product, as well as protection from mechanical damage.

  • The electronic key is equipped with a T-connector for switching with the battery.

  • Limiting operating temperatures: from -55 to 160°C.

  • The shortcircuitprotectionis provided –at any time the SC occurs, the gun stops shooting. (Protection is provided for accumulator Li-Po/Li-Io batteries of any rated capacity and LiFePo4 exceeding 20°C)

  • Compatible with batteries Li-Po/Li-Io 7.4 - 11.1 В, LiFePo4 - 9.9 В, NiMh/NiCd up to 15 V.

 

This electronic key is 100% compatible with GROM Airsoft ready-made wiring sets, it can also be used with any other wiring (using the appropriate connectors).

Electronic key GROM Airsoft SNIPER

Electronic key GROM Sniper is a multifunctional controller designed for stable gear (drive) operation at loads up to 200 m/s.

 

  • To connect this controller, you need to pre-install the ready-made wiring set in your drive (gear) from GROM airsoft electronics.

  • No additional design changes needed!

  • The controller is filled with an epoxy resin compound of a higher thermal conductivity, which means a complete sealing of a product, as well as protection from mechanical damage.

  • The controller is made on the basis of modern micro controllers and field transistors of the 3d generation due to which the controller protects the contact block from burning-off, since the current flows directly from a battery to motor.

  • Due to this a trigger response time and a fire rate are higher.

  • This controller works in conjunction with the GROM wiring sets. Modularity allows to quickly disconnect the device from the drive (gear) and, if necessary, replace it with a controller of other functionality, as well as simplify installation and diagnostics for the integrity of all wiring.

  • Please note that all GROM keys and controllers are interchangeable.

  • When using this controller, the drive (gear) can work only in the single fire mode (connectable function).

  • Thanks to the active brake, the motor stops immediately after the shot. This contributes to the fact that the piston always stops in the forward position, thereby reducing the wear of the spring. The realism of the shots is enhanced.

  • The entire programming process is performed by pressing the trigger of your AEG. There are no indicators on the controller. The sound signal produced by the motor is used as an alert. The whole process takes up to 30 seconds.

  • The controller constantly checks the voltage on the battery. Your AEG will inform you when the battery voltage value falls below an acceptable level.

  • During operation, the controller receives information about the current in the power wiring circuit. When a short circuit occurs, the drive stops shooting, thereby protecting your wiring, battery and motor. It is protected at any time of the short circuit occurrence.

  • Compatible with batteries Li-Po/Li-Io 11.1 V.

  • Switching the key is made by applying «+» to the control contact (mini-banana connector).


Attention! This electronic key is 100% compatible with GROM Airsoft ready-made wiring sets, it can also be used with any other wiring (using the appropriate connectors).

Ready-made wiring for machine gun M249-series with an output into handguard (T-connector)

The wiring set is made of silver-plated copper wire with teflon insulation thanks to which the wiring keeps its shape well and is protected from damage and abrasion.

Power wire with a cross section of 1.sq.mm, easy to fit inside gearbox and drive. The control elements a key, easy to disconnect from the wires by using mini T-connector.


Replace the key with a more functional one, so you can check wiring for a short circuit in just one second!


I t is enough to disconnect the key and test the wiring for continuity using a tester.


Limiting operating temperatures: from -55 to 160°C.


Recommended batteries: Li-Po - 7.4V / 11.lV / 14.8v; Li-Fe-Po4 - 9.9V / 13.2V; Li-Po-7.4V / 11.lV / 14.8v

Ready-made wiring for M-series with an output into handguard (T-connector)

The wiring set is made of silver-plated copper wire with teflon insulation thanks to which the wiring keeps its shape well and is protected from damage and abrasion.

Power wire with a cross section of 1.sq.mm, easy to fit inside gearbox and drive. The control elements a key, easy to disconnect from the wires by using mini T-connector.


Replace the key with a more functional one, so you can check wiring for a short circuit in just one second!


I t is enough to disconnect the key and test the wiring for continuity using a tester.


Limiting operating temperatures: from -55 to 160°C.


Recommended batteries: Li-Po - 7.4V / 11.lV / 14.8v; Li-Fe-Po4 - 9.9V / 13.2V; Li-Po-7.4V / 11.lV / 14.8v

Ready-made wiring for M-series with an output in butt (T-connector)

The wiring set is made of silver-plated copper wire with teflon insulation thanks to which the wiring keeps its shape well and is protected from damage and abrasion.

Power wire with a cross section of 1.sq.mm, easy to fit inside gearbox and drive. The control elements a key, easy to disconnect from the wires by using mini T-connector.


Replace the key with a more functional one, so you can check wiring for a short circuit in just one second!


I t is enough to disconnect the key and test the wiring for continuity using a tester.


Limiting operating temperatures: from -55 to 160°C.


Recommended batteries: Li-Po - 7.4V / 11.lV / 14.8v; Li-Fe-Po4 - 9.9V / 13.2V; Li-Po-7.4V / 11.lV / 14.8v

Ready-made wiring for G36-series with an output into handguard (T-connector)

The wiring set is made of silver-plated copper wire with teflon insulation thanks to which the wiring keeps its shape well and is protected from damage and abrasion.

Power wire with a cross section of 1.sq.mm, easy to fit inside gearbox and drive. The control elements a key, easy to disconnect from the wires by using mini T-connector.


Replace the key with a more functional one, so you can check wiring for a short circuit in just one second!


I t is enough to disconnect the key and test the wiring for continuity using a tester.


Limiting operating temperatures: from -55 to 160°C.


Recommended batteries: Li-Po - 7.4V / 11.lV / 14.8v; Li-Fe-Po4 - 9.9V / 13.2V; Li-Po-7.4V / 11.lV / 14.8v

Ready-made wiring for G36-series with an output in butt (T-connector)

The wiring set is made of silver-plated copper wire with teflon insulation thanks to which the wiring keeps its shape well and is protected from damage and abrasion.

Power wire with a cross section of 1.sq.mm, easy to fit inside gearbox and drive. The control elements a key, easy to disconnect from the wires by using mini T-connector.


Replace the key with a more functional one, so you can check wiring for a short circuit in just one second!


I t is enough to disconnect the key and test the wiring for continuity using a tester.


Limiting operating temperatures: from -55 to 160°C.


Recommended batteries: Li-Po - 7.4V / 11.lV / 14.8v; Li-Fe-Po4 - 9.9V / 13.2V; Li-Po-7.4V / 11.lV / 14.8v

Ready-made wiring for AK-series with an output under receiver cover (T-connector)

The wiring set is made of silver-plated copper wire with teflon insulation thanks to which the wiring keeps its shape well and is protected from damage and abrasion.

Power wire with a cross section of 1.sq.mm, easy to fit inside gearbox and drive. The control elements a key, easy to disconnect from the wires by using mini T-connector.


Replace the key with a more functional one, so you can check wiring for a short circuit in just one second!


I t is enough to disconnect the key and test the wiring for continuity using a tester.


Limiting operating temperatures: from -55 to 160°C.


Recommended batteries: Li-Po - 7.4V / 11.lV / 14.8v; Li-Fe-Po4 - 9.9V / 13.2V; Li-Po-7.4V / 11.lV / 14.8v

Our address:
 

Office 326A, 14/1, Likhoborskaya quay, Moscow

125438, Russia

info@gunfighters.ru

Contact us

© 2018 by Akademia

  • YouTube Social  Icon
  • Facebook Social Icon
  • Instagram Social Icon
  • Vkontakte Social Icon